보드 종료 방법에 대하여 문의 하신 것 같습니다.

Linux가 부팅된 후에 아래 명령어를 실행하시면 종료되는 것을 확인 하실 수 있습니다.

rex@rex:/$ su

root@rex:/# halt

Broadcast message from root@rex (ttySAC3) (Wed May  7 16:53:33 2014):

The system is going down for system halt NOW!

[  497.150677] [c5] s2m_rtc_read_time: 2014/5/7 16:53:37(3)

[  497.156427] [c5] s2m_rtc_read_time: 2014/5/7 16:53:37(3)

[  497.160375] [c5] s2m_rtc_set_alarm: 2014/5/7 16:53:38(3)

[  497.165935] [c5] s2m_rtc_stop_alarm: 2014/5/7 16:45:13(3)

[  497.174745] [c5] s2m_rtc_start_alarm: 2014/5/7 16:53:38(3)

[  498.120700] [c0] s2m_rtc_read_time: 2014/5/7 16:53:38(3)

[  498.126328] [c0] s2m_rtc_read_time: 2014/5/7 16:53:38(3)

[  498.130220] [c0] s2m_rtc_set_alarm: 2014/5/7 16:53:39(3)

[  498.135862] [c0] s2m_rtc_stop_alarm: 2014/5/7 16:53:38(3)

[  498.144862] [c0] s2m_rtc_start_alarm: 2014/5/7 16:53:39(3)

[  498.152182] [c0] s2m_rtc_read_time: 2014/5/7 16:53:38(3)

[  498.157741] [c0] s2m_rtc_read_time: 2014/5/7 16:53:38(3)

[  498.161636] [c0] s2m_rtc_set_alarm: 2014/5/7 16:53:39(3)

[  498.167235] [c0] s2m_rtc_stop_alarm: 2014/5/7 16:53:39(3)

[  498.175847] [c0] s2m_rtc_start_alarm: 2014/5/7 16:53:39(3)

[  498.181902] [c3] s2m_rtc_stop_alarm: 2014/5/7 16:53:39(3)

[  498.189186] [c3] s2m_rtc_read_time: 2014/5/7 16:53:38(3)

[  498.552666] [c5] s2m_rtc_set_time: 2014/5/7 16:53:38(3)

[  498.558037] [c5] s2m_rtc_read_time: 2014/5/7 16:53:38(3)

[  498.562190] [c5] s2m_rtc_stop_alarm: 2014/5/7 16:53:39(3)

[  499.075575] [c7] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)

[  501.153686] [c0] stopped thread_hotplug

[  501.264989] [c0] s2m-rtc s2m-rtc: s2m_rtc_enable_wtsr: disable WTSR

[  501.270305] [c0] s2m_rtc_shutdown: WTSR_SMPL reg(0x87)

[  501.274962] [c0] s2m_rtc_shutdown: success to disable WTSR

[  501.280429] [c0] s2m-rtc s2m-rtc: s2m_rtc_enable_smpl: disable SMPL

[  501.287177] [c0] s2m_rtc_enable_smpl: WTSR_SMPL(0x07)

[  501.304998] [c0] Power down.

[  501.306624] [c0] sec_power_off: <116>

[  501.310088] [c0] sec_power_off: se?