MV5422-LCD Linux usb3.0 테스트 메시지

젠더를 이용 usb 3.0 저장 장치 인식 유/무 테스트

[CON2 삽입 메시지]

[  267.869963] [c1] usb 3-1: new high-speed USB device number 2 using xhci-hcd

[  267.892508] [c0] usb-storage 3-1:1.0: USB Mass Storage device detected

[  267.898156] [c3] scsi0 : usb-storage 3-1:1.0

[  268.901693] [c3] scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer Glide     1.27 PQ: 0 ANSI: 6

[  268.911157] [c3] sd 0:0:0:0: Attached scsi generic sg0 type 0

[  268.912122] [c2] sd 0:0:0:0: [sda] 15330304 512-byte logical blocks: (7.84 GB/7.30 GiB)

[  268.913669] [c0] sd 0:0:0:0: [sda] Write Protect is off

[  268.914547] [c1] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA

[  268.932356] [c2]  sda: sda1

[  268.944059] [c2] sd 0:0:0:0: [sda] Attached SCSI removable disk

[USB mount]

root@rex:~# mount /dev/sda1 /mnt/nfs/

root@rex:~# cd /mnt/nfs/

root@rex:/mnt/nfs# ls

210_WinCE  4412_ICS  DCIM  mvv210_fw_org  mvv210_fw_org.zip  v210_SMDK_Test_ver0.0.ds5  v210_SMDK_Test_ver0.0.ds5.zip

root@rex:/mnt/nfs#

[CON1 삽입 메시지]

[  472.775925] [c0] exynos-dwc3 usb.1: IRQ: ID: 0

[  472.778988] [c0] exynos-dwc3 usb.1: dwc3_exynos_rsw_thread_interrupt

[  472.785390] [c0] dwc3 12000000.dwc3: Turn on host

[  472.790069] [c0] exynos-dwc3 usb.1: dwc3_exynos_runtime_resume

[  472.996577] [c1] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller

[  472.997907] [c0] exynos-dwc3 usb.1: IRQ: B_Sess: active

[  472.997969] [c0] exynos-dwc3 usb.1: dwc3_exynos_rsw_thread_interrupt

[  473.012695] [c1] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 5

[  473.021105] [c1] xhci-hcd xhci-hcd.5.auto: irq 104, io mem 0x12000000

[  473.028192] [c1] hub 5-0:1.0: USB hub found

[  473.031316] [c1] hub 5-0:1.0: 1 port detected

[  473.036281] [c1] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller

[  473.041577] [c1] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 6

[  473.050701] [c1] hub 6-0:1.0: USB hub found

[  473.053733] [c1] hub 6-0:1.0: 1 port detected

[  473.344916] [c0] usb 5-1: new high-speed USB device number 2 using xhci-hcd

[  473.367542] [c0] usb-storage 5-1:1.0: USB Mass Storage device detected

[  473.373307] [c0] scsi1 : usb-storage 5-1:1.0

[  474.376712] [c0] scsi 1:0:0:0: Direct-Access     SanDisk  Cruzer Glide     1.27 PQ: 0 ANSI: 6

[  474.386090] [c0] sd 1:0:0:0: Attached scsi generic sg0 type 0

[  474.390849] [c3] sd 1:0:0:0: [sda] 15330304 512-byte logical blocks: (7.84 GB/7.30 GiB)

[  474.400546] [c1] sd 1:0:0:0: [sda] Write Protect is off

[  474.405267] [c1] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA

[  474.430777] [c2]  sda: sda1

[  474.435462] [c2] sd 1:0:0:0: [sda] Attached SCSI removable disk

[SD mount]

root@rex:/mnt# mount /dev/sda1 nfs/

root@rex:/mnt# cd nfs/

root@rex:/mnt/nfs# ls

210_WinCE  4412_ICS  DCIM  mvv210_fw_org  mvv210_fw_org.zip  v210_SMDK_Test_ver0.0.ds5  v210_SMDK_Test_ver0.0.ds5.zip

root@rex:/mnt/nfs#