>
>MV V210 (Android 2.2), boot 중에 정상적으로 완료(Android 기본 UI 표시)되지않고,
>특정 위치에서 계속 반복되고 있는 상태입니다.
>(LCD 상에서는 화면 중앙에 \"ANDROID\" 그라데이션 표시되다가
>아주 잠깐 Android 기본 UI 표시되었다가... 바로 화면 중앙에 \"ANDROID\" 그라데이션 표시되어버립니다.)
>
>화면 중앙에 \"ANDROID\" 그라데이션 표시 ==> 아주 잠깐 Android 기본 UI 표시 ==> 화면 중앙에 \"ANDROID\" 그라데이션 표시... 반복되어됨.
>
>
>Nand Image 변경없이,
>정상적으로 사용/동작하고 있었으며..
>오후에.. 전원인가하여.. 확인하니..
>갑자기 이런 현상(정상적으로 부트를 완료하지 못하는 현상)이 나타나고 있습니다.
>
>
>시리얼포트 쪽에 메세지는 아래와 같습니다.
>
>
>
>U-Boot 1.3.4 (Feb 25 2011 - 09:26:51) for MV-V210
>
>
>CPU: S5PV210@1000MHz
> APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
> MPLL = 667MHz, EPLL = 80MHz
> HclkDsys = 166MHz, PclkDsys = 83MHz
> HclkPsys = 133MHz, PclkPsys = 66MHz
>Serial = CLKUART
>Board: SMDKV210
>MV-DRAM: 1 GB
>Flash: 8 MB
>SD/MMC: Card init fail!
>0 MB
>NAND: 256 MB
>In: serial
>Out: serial
>Err: serial
>Hit any key to stop autoboot: 0
>
>NAND read: device 0 offset 0x600000, size 0x400000
> 4194304 bytes read: OK
>
>NAND read: device 0 offset 0xb00000, size 0x300000
> 3145728 bytes read: OK
>Boot with zImage
>The input address don\'t need a virtual-to-physical translation : 20008000
>get_format
>-------- 1 --------
>## Loading init Ramdisk from Legacy Image at 21000000 ...
> Image Name: ramdisk
> Created: 2011-03-03 6:57:20 UTC
> Image Type: ARM Linux RAMDisk Image (uncompressed)
> Data Size: 1300152 Bytes = 1.2 MB
> Load Address: 30800000
> Entry Point: 30800000
> Verifying Checksum ... OK
>
>Starting kernel ...
>
>Uncompressing Linux.................................................................................................................................................................................... done, booting the kernel.
>Initializing cgroup subsys cpu
>Linux version 2.6.32.9 (hsk@hsk-VirtualBox) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #185 PREEMPT Wed Mar 2 08:47:31 KST 2011
>CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
>CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
>Machine: SMDKV210
>Ignoring unrecognised tag 0x00000000
>Ignoring unrecognised tag 0x00000000
>Ignoring unrecognised tag 0x41001099
>Memory policy: ECC disabled, Data cache writeback
>CPU S5PV210/S5PC110 (id 0x43110220)
>S3C24XX Clocks, Copyright 2004 Simtec Electronics
>copy: bad source 0
>mout_audss: bad source 0
>S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000
>s5pv210: 37748736 bytes system memory reserved for mfc at 0x40000000
>s5pv210: 37748736 bytes system memory reserved for mfc at 0x42400000
>s5pv210: 14680064 bytes system memory reserved for fimc0 at 0x44800000
>s5pv210: 9437184 bytes system memory reserved for fimc1 at 0x45600000
>s5pv210: 6291456 bytes system memory reserved for fimc2 at 0x45f00000
>s5pv210: 16777216 bytes system memory reserved for pmem at 0x46500000
>s5pv210: 10485760 bytes system memory reserved for pmem_gpu1 at 0x47500000
>s5pv210: 1048576 bytes system memory reserved for pmem_adsp at 0x47f00000
>s5pv210: 5132288 bytes system memory reserved for jpeg at 0x48000000
>s5pv210: 10485760 bytes system memory reserved for texstream at 0x484e5000
>s5pv210: 6291456 bytes system memory reserved for fimd at 0x48ee5000
>s5pv210: 6291456 bytes system memory reserved for g2d at 0x494e5000
>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
>Kernel command line: console=ttySAC2,115200 init=/linuxrc ethaddr=00:40:5c:26:0a:5b slram=dmc1,0x40000000,+0x10000000
>PID hash table entries: 2048 (order: 1, 8192 bytes)
>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
>Memory: 256MB 256MB = 512MB total
>Memory: 353024KB available (4928K code, 1092K data, 156K init, 0K highmem)
>SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>Hierarchical RCU implementation.
>NR_IRQS:339
>VIC @fc000000: id 0x00041192, vendor 0x41
>VIC @fc010000: id 0x00041192, vendor 0x41
>VIC @fc020000: id 0x00041192, vendor 0x41
>vic_pm_register: too few VICs, increase CONFIG_ARM_VIC_NR
>VIC @fc030000: id 0x00041192, vendor 0x41
>vic_pm_register: too few VICs, increase CONFIG_ARM_VIC_NR
>mult[140737]
>max_delta_ns[2147483647]
>min_delta_ns[30517]
>rate[32768]
>HZ[256]
>Console: colour dummy device 80x30
>console [ttySAC2] enabled
>Calibrating delay loop... 996.00 BogoMIPS (lpj=1945600)
>Mount-cache hash table entries: 512
>CPU: Testing write buffer coherency: ok
>regulator: core version 0.5
>NET: Registered protocol family 16
>S5PC110 Hardware version : EVT1
>
> SDKIM smdkv210_dm9000_set
> SDKIM GPICON:2222232 GPC0CON:20
>S3C Power Management, Copyright 2004 Simtec Electronics
> KSSON mv210_jack_detect_init start..
>S5PV210 Power Domain API Enable
>S5PV210: Initializing architecture
>s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
>s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
>s3c24xx-pwm s3c24xx-pwm.2: tin at 4168750, tdiv at 4168750, tin=divclk, base 12
>s3c24xx-pwm s3c24xx-pwm.3: tin at 4168750, tdiv at 4168750, tin=divclk, base 16
>bio: create slab <bio-0> at 0
>vgaarb: loaded
>SCSI subsystem initialized
>usbcore: registered new interface driver usbfs
>usbcore: registered new interface driver hub
>usbcore: registered new device driver usb
>s3c-i2c s3c2410-i2c.0: slave address 0x10
>s3c-i2c s3c2410-i2c.0: bus frequency set to 65 KHz
>s3c-i2c s3c2410-i2c.0: i2c-0: S3C I2C adapter
>s3c-i2c s3c2410-i2c.1: slave address 0x10
>s3c-i2c s3c2410-i2c.1: bus frequency set to 65 KHz
>s3c-i2c s3c2410-i2c.1: i2c-1: S3C I2C adapter
>s3c-i2c s3c2410-i2c.2: slave address 0x10
>s3c-i2c s3c2410-i2c.2: bus frequency set to 65 KHz
>s3c-i2c s3c2410-i2c.2: i2c-2: S3C I2C adapter
>Switching to clocksource clock_source_systimer
>NET: Registered protocol family 2
>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
>TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
>TCP: Hash tables configured (established 16384 bind 16384)
>TCP reno registered
>NET: Registered protocol family 1
>Trying to unpack rootfs image as initramfs...
>Freeing initrd memory: 1268K
>S5PV210 ADC driver, (c) 2010 Samsung Electronics
>Loaded driver for PL330 DMAC-0 s3c-pl330
> DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
>Loaded driver for PL330 DMAC-1 s3c-pl330
> DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
>Loaded driver for PL330 DMAC-2 s3c-pl330
> DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
>NetWinder Floating Point Emulator V0.97 (extended precision)
>ashmem: initialized
>ROMFS MTD (C) 2007 Red Hat, Inc.
>yaffs Feb 25 2011 09:07:44 Installing.
>msgmni has been set to 692
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>s3cfb s3cfb: [fb2] dma: 0x48ee5000, cpu: 0xf1000000, size: 0x002ee000
>fbcon: s3cfb (fb0) is primary device
>Console: switching to colour frame buffer device 100x30
>FIMD src sclk = 133400000
> #KSSON s3cfb_backlight_onoff onoff:1
>s3cfb s3cfb: registered successfully
>max8698_ldo_enable[252] ldo 2
>regulator: LDO2: 1100 mV
>regulator: LDO3: 1100 mV
>max8698_ldo_enable[252] ldo 4
>regulator: LDO4: 1800 mV
>regulator: LDO5: 2800 mV
>regulator: LDO6: 2600 mV
>regulator: LDO7: 2800 mV
>regulator: LDO8: 3300 mV
>regulator: LDO9: 3000 mV
>max8698_ldo_enable[252] ldo 10
>regulator: BUCK1: 750 <--> 1500 mV
>max8698_ldo_enable[252] ldo 11
>regulator: BUCK2: 950 <--> 1200 mV
>regulator: BUCK3: 1800 mV
>Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
>s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
>s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
>s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
>s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
>brd: module loaded
>loop: module loaded
>pmem: 1 init
>pmem_gpu1: 1 init
>pmem_adsp: 1 init
>S3C NAND Driver, (c) 2008 Samsung Electronics
>S3C NAND Driver is using hardware ECC.
>NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
>Creating 7 MTD partitions on \"s5pv210-nand\":
>0x0000000c0000-0x000000100000 : \"misc\"
>0x000000100000-0x000000600000 : \"recovery\"
>0x000000600000-0x000000b00000 : \"kernel\"
>0x000000b00000-0x000000e00000 : \"ramdisk\"
>0x000000e00000-0x000006800000 : \"system\"
>0x000006800000-0x000008800000 : \"cache\"
>0x000008800000-0x000010000000 : \"userdata\"
>Samsung SoC SPI Driver loaded for Bus SPI-0 with 1 Slaves attached
> Max,Min-Speed [33350000, 130273]Hz
> Irq=79 IOmem=[0xe1300fff-0xe1300000] DMA=[Rx-30, Tx-31]
>Samsung SoC SPI Driver loaded for Bus SPI-1 with 1 Slaves attached
> Max,Min-Speed [33350000, 130273]Hz
> Irq=80 IOmem=[0xe1400fff-0xe1400000] DMA=[Rx-32, Tx-33]
>smsc911x: Driver version 2008-10-21.
>smsc911x-mdio: probed
>eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
>net eth0: MAC Address: 00:40:5c:26:0a:5b
>ehci_hcd: USB 2.0 \'Enhanced\' Host Controller (EHCI) Driver
>s5pv210-ehci s5pv210-ehci: s5pv210 EHCI
>s5pv210-ehci s5pv210-ehci: new USB bus registered, assigned bus number 1
>s5pv210-ehci s5pv210-ehci: irq 87, io mem 0xec200000
>s5pv210-ehci s5pv210-ehci: USB 0.0 started, EHCI 1.00
>usb usb1: configuration #1 chosen from 1 choice
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 1 port detected
>ohci_hcd: USB 1.1 \'Open\' Host Controller (OHCI) Driver
>s5pv210-ohci s5pv210-ohci: s5pv210 OHCI
>s5pv210-ohci s5pv210-ohci: new USB bus registered, assigned bus number 2
>s5pv210-ohci s5pv210-ohci: irq 87, io mem 0xec300000
>usb usb2: configuration #1 chosen from 1 choice
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 1 port detected
>s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
>s3c-udc : version 15 March 2009 (DMA Mode)
>android init
>android_probe pdata: c055bf78
>android_bind
>android_usb gadget: android_usb ready
>Registered gadget driver \'android_usb\'
>f_adb init
>android_register_function adb
>f_mass_storage init
>android_register_function usb_mass_storage
>mass_storage_bind_config
>fsg_probe pdata: c055bf9c
>android_usb gadget: Number of LUNs=1
>adb_bind_config
>mice: could not register psaux device, error: -16
>mice: PS/2 mouse device common for all mice
>input: s3c-keypad as /devices/platform/s3c-keypad/input/input0
>s3c-keypadInitialized
>S3C Keypad Driver
>S5P Touchscreen driver, (c) 2008 Samsung Electronics
>S5P TouchScreen got loaded successfully : 12 bits
>input: S5P TouchScreen as /devices/virtual/input/input1
>input: compassinput as /devices/virtual/input/input2
> ## SDKIM cma3000_spi_probe start..
>SUCCESS: Sensor CMA3000(CHIP:37 REV:10)
>CMA3000 regs: 37 10 10 08 00 00 00 00 00 08 33 08 1c 00 00
>S3C24XX RTC, (c) 2004,2006 Simtec Electronics
>using rtc device, s3c, for alarms
>s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
>i2c /dev entries driver
>i2c-gpio i2c-gpio.3: using pins 110 (SDA) and 109 (SCL)
>Linux video capture interface: v2.00
>IPC probe success
>mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics
>
>S3C JPEG Driver, (c) 2007 Samsung Electronics
>JPEG driver for S5PV210
>S5P Rotator Driver, (c) 2008 Samsung Electronics
>rotator_probe called
>rotator_probe success
>i2c i2c-1: attached s5p_ddc into i2c adapter successfully
>S5PC11X HPD Driver, (c) 2009 Samsung Electronics
>S5PC11X CEC Driver, (c) 2009 Samsung Electronics
>s3c_bat_init
>sec-fake-battery sec-fake-battery: s3c_bat_probe
>S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
>s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
>cpuidle: using governor ladder
>cpuidle: using governor menu
>sdhci: Secure Digital Host Controller Interface driver
>sdhci: Copyright(c) Pierre Ossman
>s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
>Registered led device: mmc0::
>mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
>s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
>Registered led device: mmc1::
>mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
>s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
>Registered led device: mmc2::
>mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
>usbcore: registered new interface driver usbhid
>usbhid: v2.6:USB HID core driver
>logger: created 64K log \'log_main\'
>logger: created 256K log \'log_events\'
>logger: created 64K log \'log_radio\'
>logger: created 64K log \'log_system\'
>Advanced Linux Sound Architecture Driver Version 1.0.21.
>s3c_preallocate_dma_buffer: VA-ff01a000, PA-4F280000, 524288bytes
>asoc: WM8580 PAIFRX <-> s3c64xx-i2s mapping ok
>s3c_preallocate_dma_buffer: VA-ff09a000, PA-4F300000, 524288bytes
>asoc: WM8580 PAIFTX <-> s3c64xx-i2s mapping ok
>ASoC: Failed to create Rear-L/R debugfs file
>ASoC: Failed to create Center/Sub debugfs file
>ASoC: Failed to create Front-L/R debugfs file
>HDP Polling Task
>ALSA device list:
> #0: smdk (WM8580)
>TCP cubic registered
>NET: Registered protocol family 17
>lib80211: common routines for IEEE802.11 drivers
>VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
>regulator_init_complete: incomplete constraints, leaving VCC_MEM on
>regulator_init_complete: incomplete constraints, leaving {VADC/VSYS/VKEY}_2.8V on
>regulator_init_complete: incomplete constraints, leaving VUOTG_A_3.3V/VUHOST_A_3.3V on
>regulator_init_complete: incomplete constraints, leaving VCC_2.6V on
>regulator_init_complete: incomplete constraints, leaving VMMC_2.8V/VEXT_2.8V on
>regulator_init_complete: incomplete constraints, leaving V_MIPI_1.8V on
>regulator_init_complete: incomplete constraints, leaving VUOTG_D_1.1V/VUHOST_D_1.1V on
>s3c2410-rtc s3c2410-rtc: setting system clock to 3265-10-02 03:26:34 UTC (2235316330)
> mt9d111_init
>mmc0: new high speed SDIO card at address 0001
>Mode changed (0->1)
>[wm8580_set_outpath] path(1)
>MT9D111 0-005d: mt9d111 has been probed
>MT9D111 0-005d: fetching platform data
>MT9D111 0-005d: parallel mode
>FIMC0 registered successfully
>FIMC1 registered successfully
>FIMC2 registered successfully
>S5PC1XX LCD & TVOUT Driver, (c) 2009 Samsung Electronics
> [TV] s5p_tv_probe
>s5p-tvout s5p-tvout: hpd status is cable removed
>Freeing init memory: 156K
>init: /init.smdkv210.rc: 19: invalid option \'setprop\'
>init: /init.smdkv210.rc: 19: invalid option \'setprop\'
>init: cannot open \'/initlogo.rle\'
>PA FB = 0x48EE5000, bits per pixel = 32
>screen width=800 height=480 va=0xe8ee5000 pa=0x48ee5000
>Back frameBuffer[0].VAddr=e905c000 PAddr=4905c000 size=1536000
>yaffs: dev is 32505860 name is \"mtdblock4\"
>yaffs: passed flags \"\"
>yaffs: Attempting MTD mount on 31.4, \"mtdblock4\"
>block 23 is bad
>block 487 is bad
>yaffs_read_super: isCheckpointed 0
>save exit: isCheckpointed 1
>yaffs: dev is 32505862 name is \"mtdblock6\"
>yaffs: passed flags \"\"
>yaffs: Attempting MTD mount on 31.6, \"mtdblock6\"
>block 14 is bad
>block 404 is bad
>yaffs_read_super: isCheckpointed 0
>yaffs: dev is 32505861 name is \"mtdblock5\"
>yaffs: passed flags \"\"
>yaffs: Attempting MTD mount on 31.5, \"mtdblock5\"
>yaffs_read_super: isCheckpointed 0
>init: cannot find \'/system/etc/install-recovery.sh\', disabling \'flash_recovery\'
>enabling adb
>adb_open
>net eth0: SMSC911x/921x identified at 0xf083e000, IRQ: 41
>sh: can\'t access tty; job control turned off
># warning: `rild\' uses 32-bit capabilities (legacy support in use)
>PVR_K:(Warning): SysFinalise: Version string: SGX540 S5PC110 [581, services4/system/s5pc110/sysconfig.c]
> SDKIM smdk64xx_hw_params format:2 rate:44100
>SDKIM S3C_I2SV2_DIV_PRESCALER div:3
>DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
> SDKIM smdk64xx_hw_params format:2 rate:44100
>SDKIM S3C_I2SV2_DIV_PRESCALER div:3
>DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
>s3c-fimc: FIMC2 1 opened.
>s3c-fimc: Buffers were already requested
>
>
>
>
>
>이렇게 진행되다가.....
>아래와 같이
>binder: send failed reply for transaction ...................
>
>하며.. 반복적으로 메세지가 출력되고 있는 상태입니다...
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>request_suspend_state: wakeup (3->0) at 54185427009 (2040-10-31 17:13:03.179513044 UTC)
>binder: release 2079:2079 transaction 852 in, still active
>binder: send failed reply for transaction 852 to 2171:2171
>s3c-fimc: FIMC2 0 released.
>alarm_release: clear alarm, pending 0
>binder: release 2079:2085 transaction 919 in, still active
>request_suspend_state: wakeup (0->0) at 58251192683 (2040-10-31 17:13:07.245279510 UTC)
>binder: send failed reply for transaction 919 to 2169:2169
>binder: release 2079:2189 transaction 886 in, still active
>binder: send failed reply for transaction 886 to 2164:2164
>init: untracked pid 2021 exited
>binder: 2092:2095 transaction failed 29189, size 60-0
>init: untracked pid 2169 exited
>init: untracked pid 2171 exited
>init: untracked pid 2164 exited
> SDKIM smdk64xx_hw_params format:2 rate:44100
>SDKIM S3C_I2SV2_DIV_PRESCALER div:3
>DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
> SDKIM smdk64xx_hw_params format:2 rate:44100
>SDKIM S3C_I2SV2_DIV_PRESCALER div:3
>DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
>s3c-fimc: FIMC2 1 opened.
>s3c-fimc: Buffers were already requested
>request_suspend_state: wakeup (0->0) at 62248706058 (2040-10-31 17:13:11.242792676 UTC)
>binder: release 2270:2270 transaction 1646 out, still active
>binder: release 2200:2200 transaction 1682 in, still active
>binder: send failed reply for transaction 1682 to 2269:2269
>s3c-fimc: FIMC2 0 released.
>binder: release 2200:2205 transaction 1675 in, still active
>binder: send failed reply for transaction 1675 to 2264:2293
>binder: release 2200:2206 transaction 1676 in, still active
>binder: send failed reply for transaction 1676 to 2264:2294
>binder: release 2200:2268 transaction 1646 in, still active
>binder: send failed reply for transaction 1646, target dead
>binder: send failed reply for transaction 1683 to 2264:2264
>binder: send failed reply for transaction 1689 to 2298:2298
>binder: send failed reply for transaction 1696 to 2300:2300
>binder: release proc 2200, transaction 1684, not freed
>binder: 2211:2214 transaction failed 29189, size 60-0
>binder: 2269:2269 transaction failed 29189, size 3696-4
>alarm_release: clear alarm, pending 0
>request_suspend_state: wakeup (0->0) at 63643278794 (2040-10-31 17:13:12.637365287 UTC)
>init: untracked pid 2194 exited
>init: untracked pid 2300 exited
>init: untracked pid 2298 exited
> SDKIM smdk64xx_hw_params format:2 rate:44100
>SDKIM S3C_I2SV2_DIV_PRESCALER div:3
>DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
> SDKIM smdk64xx_hw_params format:2 rate:44100
>SDKIM S3C_I2SV2_DIV_PRESCALER div:3
>DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
>s3c-fimc: FIMC2 1 opened.
>s3c-fimc: Buffers were already requested
>request_suspend_state: wakeup (0->0) at 67603184538 (2040-10-31 17:13:16.597270948 UTC)
>binder: release 2320:2326 transaction 2445 in, still active
>binder: send failed reply for transaction 2445 to 2398:2398
>s3c-fimc: FIMC2 0 released.
>alarm_release: clear alarm, pending 0
>binder: release 2320:2384 transaction 2385 in, still active
>request_suspend_state: wakeup (0->0) at 69980077284 (2040-10-31 17:13:18.974163819 UTC)
>binder: send failed reply for transaction 2385 to 2385:2385
>binder: release 2320:2416 transaction 2387 in, still active
>binder: send failed reply for transaction 2387 to 2389:2389
>binder: release 2320:2417 transaction 2426 in, still active
>binder: send failed reply for transaction 2426 to 2392:2392
>binder: release proc 2320, transaction 2446, not freed
>binder: 2331:2334 transaction failed 29189, size 60-0
>
>
>
>
>
>
>조언 부탁드립니다.
>
>감사합니다.
>
>
>
마이크로비젼 기술지원팀입니다.

--> 같은 구간이 반복되는 현상은 메인보드와 베이스 보드간에 결합이 잘 이루어지지 않았지 때문에 발생한 것으로 보시면 됩니다.
우선적으로 메인과 베이스를 분리한 후에 다시 결합 시 잘 결합이 안되 경우가 있을 수 있습니다. 다른 한 가지 경우는 외간상으론
결합이 잘되었지만 위와 같은 현상이 발생할 때입니다. 이 경우는 메인보드 컨넥터부분에 문제가 있어 발생하는 경우입니다.
메인 컨넥터의 사이 간격이 넓어져 베이스 컨넥터와 결합하여도 잘 접속이 되지 않기 때문에 발생하는 것입니다. 이 때에는 메인
컨넥터에 압력을 가해 넓어진 간격을 좁힌 다음에 베이스와 결합하시면 문제가 해결 될 것입니다. 테스트 해보시길 바랍니다.