MV V210 (Android 2.2), boot 중에 정상적으로 완료(Android 기본 UI 표시)되지않고,
특정 위치에서 계속 반복되고 있는 상태입니다.
(LCD 상에서는 화면 중앙에 \"ANDROID\" 그라데이션 표시되다가
아주 잠깐 Android 기본 UI 표시되었다가... 바로 화면 중앙에 \"ANDROID\" 그라데이션 표시되어버립니다.)

화면 중앙에 \"ANDROID\" 그라데이션 표시 ==> 아주 잠깐 Android 기본 UI 표시 ==> 화면 중앙에 \"ANDROID\" 그라데이션 표시... 반복되어됨.


Nand Image 변경없이,
정상적으로 사용/동작하고 있었으며..
오후에.. 전원인가하여.. 확인하니..
갑자기 이런 현상(정상적으로 부트를 완료하지 못하는 현상)이 나타나고 있습니다.


시리얼포트 쪽에 메세지는 아래와 같습니다.



U-Boot 1.3.4 (Feb 25 2011 - 09:26:51) for MV-V210


CPU: S5PV210@1000MHz
APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
MPLL = 667MHz, EPLL = 80MHz
HclkDsys = 166MHz, PclkDsys = 83MHz
HclkPsys = 133MHz, PclkPsys = 66MHz
Serial = CLKUART
Board: SMDKV210
MV-DRAM: 1 GB
Flash: 8 MB
SD/MMC: Card init fail!
0 MB
NAND: 256 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x600000, size 0x400000
4194304 bytes read: OK

NAND read: device 0 offset 0xb00000, size 0x300000
3145728 bytes read: OK
Boot with zImage
The input address don\'t need a virtual-to-physical translation : 20008000
get_format
-------- 1 --------
## Loading init Ramdisk from Legacy Image at 21000000 ...
Image Name: ramdisk
Created: 2011-03-03 6:57:20 UTC
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 1300152 Bytes = 1.2 MB
Load Address: 30800000
Entry Point: 30800000
Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux.................................................................................................................................................................................... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 2.6.32.9 (hsk@hsk-VirtualBox) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #185 PREEMPT Wed Mar 2 08:47:31 KST 2011
CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDKV210
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41001099
Memory policy: ECC disabled, Data cache writeback
CPU S5PV210/S5PC110 (id 0x43110220)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
copy: bad source 0
mout_audss: bad source 0
S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000
s5pv210: 37748736 bytes system memory reserved for mfc at 0x40000000
s5pv210: 37748736 bytes system memory reserved for mfc at 0x42400000
s5pv210: 14680064 bytes system memory reserved for fimc0 at 0x44800000
s5pv210: 9437184 bytes system memory reserved for fimc1 at 0x45600000
s5pv210: 6291456 bytes system memory reserved for fimc2 at 0x45f00000
s5pv210: 16777216 bytes system memory reserved for pmem at 0x46500000
s5pv210: 10485760 bytes system memory reserved for pmem_gpu1 at 0x47500000
s5pv210: 1048576 bytes system memory reserved for pmem_adsp at 0x47f00000
s5pv210: 5132288 bytes system memory reserved for jpeg at 0x48000000
s5pv210: 10485760 bytes system memory reserved for texstream at 0x484e5000
s5pv210: 6291456 bytes system memory reserved for fimd at 0x48ee5000
s5pv210: 6291456 bytes system memory reserved for g2d at 0x494e5000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
Kernel command line: console=ttySAC2,115200 init=/linuxrc ethaddr=00:40:5c:26:0a:5b slram=dmc1,0x40000000,+0x10000000
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 353024KB available (4928K code, 1092K data, 156K init, 0K highmem)
SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:339
VIC @fc000000: id 0x00041192, vendor 0x41
VIC @fc010000: id 0x00041192, vendor 0x41
VIC @fc020000: id 0x00041192, vendor 0x41
vic_pm_register: too few VICs, increase CONFIG_ARM_VIC_NR
VIC @fc030000: id 0x00041192, vendor 0x41
vic_pm_register: too few VICs, increase CONFIG_ARM_VIC_NR
mult[140737]
max_delta_ns[2147483647]
min_delta_ns[30517]
rate[32768]
HZ[256]
Console: colour dummy device 80x30
console [ttySAC2] enabled
Calibrating delay loop... 996.00 BogoMIPS (lpj=1945600)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
S5PC110 Hardware version : EVT1

SDKIM smdkv210_dm9000_set
SDKIM GPICON:2222232 GPC0CON:20
S3C Power Management, Copyright 2004 Simtec Electronics
KSSON mv210_jack_detect_init start..
S5PV210 Power Domain API Enable
S5PV210: Initializing architecture
s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
s3c24xx-pwm s3c24xx-pwm.2: tin at 4168750, tdiv at 4168750, tin=divclk, base 12
s3c24xx-pwm s3c24xx-pwm.3: tin at 4168750, tdiv at 4168750, tin=divclk, base 16
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2410-i2c.0: slave address 0x10
s3c-i2c s3c2410-i2c.0: bus frequency set to 65 KHz
s3c-i2c s3c2410-i2c.0: i2c-0: S3C I2C adapter
s3c-i2c s3c2410-i2c.1: slave address 0x10
s3c-i2c s3c2410-i2c.1: bus frequency set to 65 KHz
s3c-i2c s3c2410-i2c.1: i2c-1: S3C I2C adapter
s3c-i2c s3c2410-i2c.2: slave address 0x10
s3c-i2c s3c2410-i2c.2: bus frequency set to 65 KHz
s3c-i2c s3c2410-i2c.2: i2c-2: S3C I2C adapter
Switching to clocksource clock_source_systimer
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 1268K
S5PV210 ADC driver, (c) 2010 Samsung Electronics
Loaded driver for PL330 DMAC-0 s3c-pl330
DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
Loaded driver for PL330 DMAC-1 s3c-pl330
DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
Loaded driver for PL330 DMAC-2 s3c-pl330
DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
NetWinder Floating Point Emulator V0.97 (extended precision)
ashmem: initialized
ROMFS MTD (C) 2007 Red Hat, Inc.
yaffs Feb 25 2011 09:07:44 Installing.
msgmni has been set to 692
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
s3cfb s3cfb: [fb2] dma: 0x48ee5000, cpu: 0xf1000000, size: 0x002ee000
fbcon: s3cfb (fb0) is primary device
Console: switching to colour frame buffer device 100x30
FIMD src sclk = 133400000
#KSSON s3cfb_backlight_onoff onoff:1
s3cfb s3cfb: registered successfully
max8698_ldo_enable[252] ldo 2
regulator: LDO2: 1100 mV
regulator: LDO3: 1100 mV
max8698_ldo_enable[252] ldo 4
regulator: LDO4: 1800 mV
regulator: LDO5: 2800 mV
regulator: LDO6: 2600 mV
regulator: LDO7: 2800 mV
regulator: LDO8: 3300 mV
regulator: LDO9: 3000 mV
max8698_ldo_enable[252] ldo 10
regulator: BUCK1: 750 <--> 1500 mV
max8698_ldo_enable[252] ldo 11
regulator: BUCK2: 950 <--> 1200 mV
regulator: BUCK3: 1800 mV
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
pmem: 1 init
pmem_gpu1: 1 init
pmem_adsp: 1 init
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Creating 7 MTD partitions on \"s5pv210-nand\":
0x0000000c0000-0x000000100000 : \"misc\"
0x000000100000-0x000000600000 : \"recovery\"
0x000000600000-0x000000b00000 : \"kernel\"
0x000000b00000-0x000000e00000 : \"ramdisk\"
0x000000e00000-0x000006800000 : \"system\"
0x000006800000-0x000008800000 : \"cache\"
0x000008800000-0x000010000000 : \"userdata\"
Samsung SoC SPI Driver loaded for Bus SPI-0 with 1 Slaves attached
Max,Min-Speed [33350000, 130273]Hz
Irq=79 IOmem=[0xe1300fff-0xe1300000] DMA=[Rx-30, Tx-31]
Samsung SoC SPI Driver loaded for Bus SPI-1 with 1 Slaves attached
Max,Min-Speed [33350000, 130273]Hz
Irq=80 IOmem=[0xe1400fff-0xe1400000] DMA=[Rx-32, Tx-33]
smsc911x: Driver version 2008-10-21.
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
net eth0: MAC Address: 00:40:5c:26:0a:5b
ehci_hcd: USB 2.0 \'Enhanced\' Host Controller (EHCI) Driver
s5pv210-ehci s5pv210-ehci: s5pv210 EHCI
s5pv210-ehci s5pv210-ehci: new USB bus registered, assigned bus number 1
s5pv210-ehci s5pv210-ehci: irq 87, io mem 0xec200000
s5pv210-ehci s5pv210-ehci: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 \'Open\' Host Controller (OHCI) Driver
s5pv210-ohci s5pv210-ohci: s5pv210 OHCI
s5pv210-ohci s5pv210-ohci: new USB bus registered, assigned bus number 2
s5pv210-ohci s5pv210-ohci: irq 87, io mem 0xec300000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android init
android_probe pdata: c055bf78
android_bind
android_usb gadget: android_usb ready
Registered gadget driver \'android_usb\'
f_adb init
android_register_function adb
f_mass_storage init
android_register_function usb_mass_storage
mass_storage_bind_config
fsg_probe pdata: c055bf9c
android_usb gadget: Number of LUNs=1
adb_bind_config
mice: could not register psaux device, error: -16
mice: PS/2 mouse device common for all mice
input: s3c-keypad as /devices/platform/s3c-keypad/input/input0
s3c-keypadInitialized
S3C Keypad Driver
S5P Touchscreen driver, (c) 2008 Samsung Electronics
S5P TouchScreen got loaded successfully : 12 bits
input: S5P TouchScreen as /devices/virtual/input/input1
input: compassinput as /devices/virtual/input/input2
## SDKIM cma3000_spi_probe start..
SUCCESS: Sensor CMA3000(CHIP:37 REV:10)
CMA3000 regs: 37 10 10 08 00 00 00 00 00 08 33 08 1c 00 00
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
using rtc device, s3c, for alarms
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
i2c-gpio i2c-gpio.3: using pins 110 (SDA) and 109 (SCL)
Linux video capture interface: v2.00
IPC probe success
mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics

S3C JPEG Driver, (c) 2007 Samsung Electronics
JPEG driver for S5PV210
S5P Rotator Driver, (c) 2008 Samsung Electronics
rotator_probe called
rotator_probe success
i2c i2c-1: attached s5p_ddc into i2c adapter successfully
S5PC11X HPD Driver, (c) 2009 Samsung Electronics
S5PC11X CEC Driver, (c) 2009 Samsung Electronics
s3c_bat_init
sec-fake-battery sec-fake-battery: s3c_bat_probe
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
Registered led device: mmc0::
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
Registered led device: mmc1::
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
Registered led device: mmc2::
mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log \'log_main\'
logger: created 256K log \'log_events\'
logger: created 64K log \'log_radio\'
logger: created 64K log \'log_system\'
Advanced Linux Sound Architecture Driver Version 1.0.21.
s3c_preallocate_dma_buffer: VA-ff01a000, PA-4F280000, 524288bytes
asoc: WM8580 PAIFRX <-> s3c64xx-i2s mapping ok
s3c_preallocate_dma_buffer: VA-ff09a000, PA-4F300000, 524288bytes
asoc: WM8580 PAIFTX <-> s3c64xx-i2s mapping ok
ASoC: Failed to create Rear-L/R debugfs file
ASoC: Failed to create Center/Sub debugfs file
ASoC: Failed to create Front-L/R debugfs file
HDP Polling Task
ALSA device list:
#0: smdk (WM8580)
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
regulator_init_complete: incomplete constraints, leaving VCC_MEM on
regulator_init_complete: incomplete constraints, leaving {VADC/VSYS/VKEY}_2.8V on
regulator_init_complete: incomplete constraints, leaving VUOTG_A_3.3V/VUHOST_A_3.3V on
regulator_init_complete: incomplete constraints, leaving VCC_2.6V on
regulator_init_complete: incomplete constraints, leaving VMMC_2.8V/VEXT_2.8V on
regulator_init_complete: incomplete constraints, leaving V_MIPI_1.8V on
regulator_init_complete: incomplete constraints, leaving VUOTG_D_1.1V/VUHOST_D_1.1V on
s3c2410-rtc s3c2410-rtc: setting system clock to 3265-10-02 03:26:34 UTC (2235316330)
mt9d111_init
mmc0: new high speed SDIO card at address 0001
Mode changed (0->1)
[wm8580_set_outpath] path(1)
MT9D111 0-005d: mt9d111 has been probed
MT9D111 0-005d: fetching platform data
MT9D111 0-005d: parallel mode
FIMC0 registered successfully
FIMC1 registered successfully
FIMC2 registered successfully
S5PC1XX LCD & TVOUT Driver, (c) 2009 Samsung Electronics
[TV] s5p_tv_probe
s5p-tvout s5p-tvout: hpd status is cable removed
Freeing init memory: 156K
init: /init.smdkv210.rc: 19: invalid option \'setprop\'
init: /init.smdkv210.rc: 19: invalid option \'setprop\'
init: cannot open \'/initlogo.rle\'
PA FB = 0x48EE5000, bits per pixel = 32
screen width=800 height=480 va=0xe8ee5000 pa=0x48ee5000
Back frameBuffer[0].VAddr=e905c000 PAddr=4905c000 size=1536000
yaffs: dev is 32505860 name is \"mtdblock4\"
yaffs: passed flags \"\"
yaffs: Attempting MTD mount on 31.4, \"mtdblock4\"
block 23 is bad
block 487 is bad
yaffs_read_super: isCheckpointed 0
save exit: isCheckpointed 1
yaffs: dev is 32505862 name is \"mtdblock6\"
yaffs: passed flags \"\"
yaffs: Attempting MTD mount on 31.6, \"mtdblock6\"
block 14 is bad
block 404 is bad
yaffs_read_super: isCheckpointed 0
yaffs: dev is 32505861 name is \"mtdblock5\"
yaffs: passed flags \"\"
yaffs: Attempting MTD mount on 31.5, \"mtdblock5\"
yaffs_read_super: isCheckpointed 0
init: cannot find \'/system/etc/install-recovery.sh\', disabling \'flash_recovery\'
enabling adb
adb_open
net eth0: SMSC911x/921x identified at 0xf083e000, IRQ: 41
sh: can\'t access tty; job control turned off
# warning: `rild\' uses 32-bit capabilities (legacy support in use)
PVR_K:(Warning): SysFinalise: Version string: SGX540 S5PC110 [581, services4/system/s5pc110/sysconfig.c]
SDKIM smdk64xx_hw_params format:2 rate:44100
SDKIM S3C_I2SV2_DIV_PRESCALER div:3
DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
SDKIM smdk64xx_hw_params format:2 rate:44100
SDKIM S3C_I2SV2_DIV_PRESCALER div:3
DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
s3c-fimc: FIMC2 1 opened.
s3c-fimc: Buffers were already requested





이렇게 진행되다가.....
아래와 같이
binder: send failed reply for transaction ...................

하며.. 반복적으로 메세지가 출력되고 있는 상태입니다...














request_suspend_state: wakeup (3->0) at 54185427009 (2040-10-31 17:13:03.179513044 UTC)
binder: release 2079:2079 transaction 852 in, still active
binder: send failed reply for transaction 852 to 2171:2171
s3c-fimc: FIMC2 0 released.
alarm_release: clear alarm, pending 0
binder: release 2079:2085 transaction 919 in, still active
request_suspend_state: wakeup (0->0) at 58251192683 (2040-10-31 17:13:07.245279510 UTC)
binder: send failed reply for transaction 919 to 2169:2169
binder: release 2079:2189 transaction 886 in, still active
binder: send failed reply for transaction 886 to 2164:2164
init: untracked pid 2021 exited
binder: 2092:2095 transaction failed 29189, size 60-0
init: untracked pid 2169 exited
init: untracked pid 2171 exited
init: untracked pid 2164 exited
SDKIM smdk64xx_hw_params format:2 rate:44100
SDKIM S3C_I2SV2_DIV_PRESCALER div:3
DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
SDKIM smdk64xx_hw_params format:2 rate:44100
SDKIM S3C_I2SV2_DIV_PRESCALER div:3
DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
s3c-fimc: FIMC2 1 opened.
s3c-fimc: Buffers were already requested
request_suspend_state: wakeup (0->0) at 62248706058 (2040-10-31 17:13:11.242792676 UTC)
binder: release 2270:2270 transaction 1646 out, still active
binder: release 2200:2200 transaction 1682 in, still active
binder: send failed reply for transaction 1682 to 2269:2269
s3c-fimc: FIMC2 0 released.
binder: release 2200:2205 transaction 1675 in, still active
binder: send failed reply for transaction 1675 to 2264:2293
binder: release 2200:2206 transaction 1676 in, still active
binder: send failed reply for transaction 1676 to 2264:2294
binder: release 2200:2268 transaction 1646 in, still active
binder: send failed reply for transaction 1646, target dead
binder: send failed reply for transaction 1683 to 2264:2264
binder: send failed reply for transaction 1689 to 2298:2298
binder: send failed reply for transaction 1696 to 2300:2300
binder: release proc 2200, transaction 1684, not freed
binder: 2211:2214 transaction failed 29189, size 60-0
binder: 2269:2269 transaction failed 29189, size 3696-4
alarm_release: clear alarm, pending 0
request_suspend_state: wakeup (0->0) at 63643278794 (2040-10-31 17:13:12.637365287 UTC)
init: untracked pid 2194 exited
init: untracked pid 2300 exited
init: untracked pid 2298 exited
SDKIM smdk64xx_hw_params format:2 rate:44100
SDKIM S3C_I2SV2_DIV_PRESCALER div:3
DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
SDKIM smdk64xx_hw_params format:2 rate:44100
SDKIM S3C_I2SV2_DIV_PRESCALER div:3
DmaAddr=@4f280000 Total=65536bytes PrdSz=8192 #Prds=2, dmaEnd 0x4f290000
s3c-fimc: FIMC2 1 opened.
s3c-fimc: Buffers were already requested
request_suspend_state: wakeup (0->0) at 67603184538 (2040-10-31 17:13:16.597270948 UTC)
binder: release 2320:2326 transaction 2445 in, still active
binder: send failed reply for transaction 2445 to 2398:2398
s3c-fimc: FIMC2 0 released.
alarm_release: clear alarm, pending 0
binder: release 2320:2384 transaction 2385 in, still active
request_suspend_state: wakeup (0->0) at 69980077284 (2040-10-31 17:13:18.974163819 UTC)
binder: send failed reply for transaction 2385 to 2385:2385
binder: release 2320:2416 transaction 2387 in, still active
binder: send failed reply for transaction 2387 to 2389:2389
binder: release 2320:2417 transaction 2426 in, still active
binder: send failed reply for transaction 2426 to 2392:2392
binder: release proc 2320, transaction 2446, not freed
binder: 2331:2334 transaction failed 29189, size 60-0






조언 부탁드립니다.

감사합니다.