@ serial 콘솔에서

fdisk -c 0

fatformat mmc 0:1

ext3format mmc 0:2

ext3format mmc 0:3

ext3format mmc 0:4

setenv bootcmd 'movi read kernel 0 40008000;movi read rootfs 0 41000000 100000;bootm 40008000 4100000'

saveenv

fastboot

@ pc에서

fastboot flash bootloader img_android\u-boot.bin

fastboot flash kernel img_android\zImage.3.0.15

fastboot flash ramdisk img_android\ramdisk-uboot.4.0.img

fastboot flash system img_android\system.4.0.img

안녕하세요. 310에 ICS를 업데이트 하는데 몇가지 문제가 있어 글을 남깁니다.

우선 아래의 방법으로 fastboot에서 업데이트시에 system.img 가 커서 올라가지

않는 메시지가 나옵니다. ext3로 포맷을 했는데, 메시지가 좀 이상한것 같네요.

문서에서 나오는 메시지와 다르게 나와서 이 부분도 확인히 필요하겠네요.

MVV310eMMC # ext3format mmc 0:2
Start format MMC0 partition2 ....
** Partition2 is not ext2 file-system 0 **
Partition2: Start Address(0xb1e4), Size(0x3f00c)
Start ext2format...
Wirte 0/1block-group
Reserved blocks for jounaling : 1025
Start write addr : 0xb1e4
...........Erase inode table(0) - 0xb23c................................
.........MVV310eMMC #

위와 같이 메시지가 나오고 나중에 host 에서 system.img 업데이트 할때 아래와 같은 메시지가

나와서 업데이트가 안되네요.

D:\work\tools>fastboot flash system img_android\system.4.0.img
sending 'system' (159301 KB)...
FAILED (remote: data too large)
finished. total time: 0.009s

그런데 위의 메시지는 처음에는 정상적으로 fastboot를 업데이트를 했습니다. ext3format도

정상적으로 되었고, flashing도 정상적으로 되었는데요. 그런데, 업데이트후에 부팅할때

제대로 부팅이 안되고 아래와 같은 에러 메시지와 함께 LCD에는 파랑,초록,빨강 색깔로

나뉘어져서 화면이 시현되고 부팅이 멈췄습니다. 아래 로그를 참조 바랍니다.

---------------------------------------------------------------------------------
U-Boot 2010.03-svn120 (Apr 20 2012 - 09:10:03) for SMDKV310 Android

        APLL = 800MHz, MPLL = 800MHz
PMIC:   ARM 1.20V, INT 1.16V, G3D 1.11V
Board:  smdkv310
MV-DRAM:         1 GB
MMC:   Warning: cannot find the raw area table(c3e3d060) 00000000
        #SDKIM OmPin:0
fwbl1: 0
bl1: 0
bl2: 32
env: 1088
knl: 1120
rfs: 9312
rfs: 9312
        7576 MB
*** Warning - using default environment

In:    serial
Out:   serial
Err:   serial
INF_REG3_REG:6

Checking Boot Mode ... EMMC4.41
board_late_init
Hit any key to stop autoboot:  0
reading kernel.. 1120, 8192
MMC read: dev # 0, block # 1120, count 8192 ...8192 blocks read: OK
completed
reading RFS.. 9312, 2048
MMC read: dev # 0, block # 9312, count 2048 ...2048 blocks read: OK
completed
Boot with zImage
## Loading init Ramdisk from Legacy Image at 41000000 ...
   Image Name:   ramdisk
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    330133 Bytes = 322.4 kB
   Load Address: 40800000
   Entry Point:  40800000

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 3.0.15-svn150 (sdkim@sdkim-desktop) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #380 SMP PREEMPT Fri Apr 20 17:17:52 KST 2012
CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: SMDKV310
Memory policy: ECC disabled, Data cache writealloc
CPU EXYNOS4210 (id 0x43210011)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
s3c_register_clksrc: clock audiocdclk has no registers set
audiocdclk: no parent clock specified
s3c_register_clksrc: clock armclk has no registers set
EXYNOS4: PLL settings, A=800000000, M=800000000, E=96000000 V=108000000
EXYNOS4: ARMCLK=800000000, DMC=400000000, ACLK200=200000000
ACLK160=160000000, ACLK133=133333333, ACLK100=100000000
uclk1: source is mout_mpll (6), rate is 100000000
uclk1: source is mout_mpll (6), rate is 100000000
uclk1: source is mout_mpll (6), rate is 100000000
uclk1: source is mout_mpll (6), rate is 100000000
sclk_csis: source is xusbxti (1), rate is 24000000
sclk_csis: source is xusbxti (1), rate is 24000000
sclk_cam0: source is xusbxti (1), rate is 24000000
sclk_cam1: source is xusbxti (1), rate is 24000000
sclk_fimc: source is xusbxti (1), rate is 24000000
sclk_fimc: source is xusbxti (1), rate is 24000000
sclk_fimc: source is xusbxti (1), rate is 24000000
sclk_fimc: source is xusbxti (1), rate is 24000000
sclk_fimd: source is xusbxti (1), rate is 24000000
sclk_fimd: source is xusbxti (1), rate is 24000000
sclk_mfc: source is mout_mfc0 (0), rate is 200000000
sclk_g3d: source is mout_g3d0 (0), rate is 33333333
sclk_pwi: source is xusbxti (1), rate is 12000000
PERCPU: Embedded 7 pages/cpu @c185a000 s6400 r8192 d14080 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
Kernel command line: console=ttySAC1,115200n8 androidboot.console=ttySAC1
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 769632k/769632k available, 278944k reserved, 294912K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xfea00000 - 0xffe00000   (  20 MB)
    vmalloc : 0xee800000 - 0xf6000000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xee000000   ( 736 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .init : 0xc0008000 - 0xc003a000   ( 200 kB)
      .text : 0xc003a000 - 0xc0671000   (6364 kB)
      .data : 0xc0672000 - 0xc06f88a0   ( 539 kB)
       .bss : 0xc06f88c4 - 0xc082fe88   (1246 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:456
Calibrating delay loop... 1590.88 BogoMIPS (lpj=3977216)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys cpuacct
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated (3181.77 BogoMIPS).
print_constraints: dummy:
NET: Registered protocol family 16
exynos4_pmu_init: PMU supports 4210(72)
S3C Power Management, Copyright 2004 Simtec Electronics
EXYNOS4: Initializing architecture
s3c-adc s5pv210-adc: attached adc driver
samsung-pd samsung-pd.0: power domain registered
samsung-pd samsung-pd.1: power domain registered
samsung-pd samsung-pd.2: power domain registered
samsung-pd samsung-pd.3: power domain registered
samsung-pd samsung-pd.5: power domain registered
samsung-pd samsung-pd.4: power domain registered
samsung-pd samsung-pd.6: power domain registered
s3c24xx-pwm s3c24xx-pwm.1: tin at 100000000, tdiv at 100000000, tin=divclk, base 8
UMP: UMP device driver 161M loaded
s5p-sysmmu s5p-sysmmu.1: Initialized for s3c-fimc.0.
s5p-sysmmu s5p-sysmmu.2: Initialized for s3c-fimc.1.
s5p-sysmmu s5p-sysmmu.3: Initialized for s3c-fimc.2.
s5p-sysmmu s5p-sysmmu.4: Initialized for s3c-fimc.3.
s5p-sysmmu s5p-sysmmu.5: Initialized for s5p-jpeg.
s5p-sysmmu s5p-sysmmu.9: Initialized for s5p-fimg2d.
s5p-sysmmu s5p-sysmmu.12: Initialized for s5p-tvout.
s5p-sysmmu s5p-sysmmu.13: Initialized for s3c-mfc.
s5p-sysmmu s5p-sysmmu.14: Initialized for s3c-mfc.
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.8: using pins 123 (SDA) and 122 (SCL)
max8649 0-0060: Detected max8952 (ID: 0x201a)
print_constraints: vdd_arm range: 770 <--> 1400 mV at 1200 mV
max8649 0-0060: max8952 regulator device is detected.
s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
max8649 1-0060: Detected max8952 (ID: 0x201a)
print_constraints: vdd_int range: 770 <--> 1380 mV at 1180 mV
max8649 1-0060: max8952 regulator device is detected.
s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
max8649 2-0060: Detected max8952 (ID: 0x201a)
print_constraints: vdd_g3d range: 900 <--> 1200 mV at 1100 mV
max8649 2-0060: max8952 regulator device is detected.
s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
s3c-i2c s3c2440-i2c.5: i2c-5: S3C I2C adapter
s3c-i2c s3c2440-i2c.6: i2c-6: S3C I2C adapter
s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.24.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource mct-frc
Switched to NOHz mode on CPU #0
Switched to NOHz mode on CPU #1
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 320K
PMU: registered new PMU device of type 0
input: wakeup_assist as /devices/platform/wakeup_assist.0/input/input0
Loaded driver for PL330 DMAC-0 s3c-pl330
        DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
Loaded driver for PL330 DMAC-1 s3c-pl330
        DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
Loaded driver for PL330 DMAC-2 s3c-pl330
        DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
highmem bounce pool size: 64 pages
ashmem: initialized
fuse init (API version 7.16)
msgmni has been set to 927
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
s3cfb s3cfb.0: [fb2] dma: 0x6aff4000, cpu: 0xee859000, size: 0x004b0000
s3cfb s3cfb.0: registered successfully
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s5pv210-uart.0: ttySAC0 at MMIO 0x13800000 (irq = 16) is a S3C6400/10
s5pv210-uart.1: ttySAC1 at MMIO 0x13810000 (irq = 20) is a S3C6400/10
console [ttySAC1] enabled
s5pv210-uart.2: ttySAC2 at MMIO 0x13820000 (irq = 24) is a S3C6400/10
s5pv210-uart.3: ttySAC3 at MMIO 0x13830000 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
i2c-core: driver [wm8994] using legacy suspend method
i2c-core: driver [wm8994] using legacy resume method
smsc911x: Driver version 2008-10-21
smsc911x-mdio: probed
smsc911x smsc911x: eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)
smsc911x smsc911x: eth0: MAC Address: ba:b0:be:ad:00:00
MAC Address: ba:b0:be:ad:00:00
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
cdc_ncm: 04-Aug-2011
usbcore: registered new interface driver cdc_ncm
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
s5p-ehci s5p-ehci: S5P EHCI Host Controller
s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
s5p-ehci s5p-ehci: irq 134, io mem 0x12580000
s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s5p-ohci s5p-ohci: Already power on PHY
s5p-ohci s5p-ohci: s5p OHCI
s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
s5p-ohci s5p-ohci: irq 134, io mem 0x12590000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
s3c-udc : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009
android_usb gadget: Mass Storage Function, version: 2009/09/11
android_usb gadget: Number of LUNs=1
 lun0: LUN: removable file: (no medium)
android_usb gadget: android_usb ready
Registered gadget driver 'android_usb'
mousedev: PS/2 mouse device common for all mice
input: samsung-keypad as /devices/platform/samsung-keypad/input/input1
usbcore: registered new interface driver xpad
usbcore: registered new interface driver usb_acecad
acecad: v3.2:USB Acecad Flair tablet driver
usbcore: registered new interface driver aiptek
aiptek: v2.3 (May 2, 2007):Aiptek HyperPen USB Tablet Driver (Linux 2.6.x)
aiptek: Bryan W. Headley/Chris Atenasio/Cedric Brun/Rene van Paassen
usbcore: registered new interface driver gtco
GTCO usb driver version: 2.00.0006
usbcore: registered new interface driver hanwang
usbcore: registered new interface driver kbtab
kbtab: v0.0.2:USB KB Gear JamStudio Tablet driver
usbcore: registered new interface driver wacom
wacom: v1.52:USB Wacom tablet driver
input: EP0700 Touchscreen as /devices/virtual/input/input2
ep0700_probe OK
        #SDKIM cma3000_driver_init
input: amosensor as /devices/virtual/input/input3
        #SDKIM cma3000_spi_probe
id:5b CMA3000_DEVICE_ID:37
SUCCESS: Sensor CMA3000(CHIP:5b REV:10)
CMA3000 regs: 5b 10 b3 00 00 00 fb fc d3 08 33 08 1c 00 00
wake enabled for irq 352
GPIO Input Driver: Start gpio inputs for smdkv310-keypad in interrupt mode
input: smdkv310-keypad as /devices/virtual/input/input4
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
using rtc device, s3c, for alarms
s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
Linux media interface: v0.10
lirc_dev: IR Remote Control driver registered, major 251
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR LIRC bridge handler initialized
Linux video capture interface: v2.00
Initialize JPEG driver
i2c i2c-1: attached s5p_ddc into i2c adapter successfully
i2c-core: driver [s5p_ddc] using legacy suspend method
i2c-core: driver [s5p_ddc] using legacy resume method
S5P HPD Driver, (c) 2009 Samsung Electronics
S5P CEC Driver, (c) 2009 Samsung Electronics
MFC(Multi Function Codec - FIMV v5.x) registered successfully
Mali: init_mali_clock mali_clock c0687ff8
Mali: Mali device driver 161M loaded
samsung-fake-battery samsung-fake-battery: samsung_fake_bat_probe
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
mshci: Mobile Storage Host Controller Interface driver
mshci: Copyright (c) 2011 Samsung Electronics Co., Ltd
dw_mmc dw_mmc: clock source 0: sclk_dwmci (160000000 Hz)
mmc0: Version ID 0x5342230a.
mmc0: FIFO WMARK FOR RX 0x20 WX 0x1. ###########
mmc0: MSHCI controller on samsung-mshci [dw_mmc] using IDMA
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (88888888 Hz)
mmc1: no vmmc regulator found
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (88888888 Hz)
mmc0: cmd 52 response timeout error
mmc2: no vmmc regulator found
mmc0: cmd 52 response timeout error
mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
mmc0: cmd 8 response timeout error
mmc0: cmd 5 response timeout error
mmc0: cmd 5 response timeout error
mmc0: cmd 5 response timeout error
mmc0: cmd 5 response timeout error
mmc0: cmd 55 response timeout error
mmc0: cmd 55 response timeout error
mmc0: cmd 55 response timeout error
usbcore: registered new interface driver usbhid
mmc0: cmd 55 response timeout error
usbhid: USB HID core driver
logger: created 256K log 'log_main'
logger: created 256K log 'log_events'
logger: created 256K log 'log_radio'
logger: created 256K log 'log_system'
Samsung Audio Subsystem Driver, (c) 2011 Samsung Electronics
audss_init: RCLK SRC[busclk]
mvv310_wm8580_gpio_irq request_irq OK gpio:217 irq:376
asoc: wm8580-hifi-playback <-> samsung-i2s.0 mapping ok
mvv310_wm8580_gpio_irq request_irq OK gpio:218 irq:377
asoc: wm8580-hifi-capture <-> samsung-i2s.0 mapping ok
Samsung SRP driver, (c)2011 Samsung Electronics
ALSA device list:
  #0: SMDK-I2S
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    Actions configured
TCP cubic registered
NET: Registered protocol family 10
Mobile IPv6
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
NET: Registered protocol family 35
lib80211: common routines for IEEE802.11 drivers
EXYNOS4210: Adaptive Support Voltage init
exynos4210_check_vdd_arm: current vdd_arm(1200000uV)
<6>Support 1.2GHz
<6>ASV Group for This Exynos4210 is 0x40000003
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
mmc0: new high speed MMC card at address 0001
Registering SWP/SWPB emulation handler
DVFS : VDD_ARM Voltage table set with 3 Group
mmcblk0: mmc0:0001 SEM08G 7.39 GiB
mmcblk0boot0: mmc0:0001 SEM08G partition 1 1.00 MiB
exynos4_integrated_dvfs_hotplug_init, max(1200000),min(200000)
mmcblk0boot1: mmc0:0001 SEM08G partition 2 1.00 MiB
s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-27 01:04:44 UTC (948935084)
 mmcblk0: p1 p2 p3 p4
FIMC0 registered successfully
FIMC1 registered successfully
FIMC2 registered successfully
FIMC3 registered successfully
S5P TVOUT Driver v3.0 (c) 2010 Samsung Electronics
 mmcblk0boot1: unknown partition table
Freeing init memory: 200K
 mmcblk0boot0: unknown partition table
MFC F/W loaded successfully (size: 360008)
EXT4-fs (mmcblk0p2): VFS: Can't find ext4 filesystem
EXT4-fs (mmcblk0p3): warning: checktime reached, running e2fsck is recommended
EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p4): warning: checktime reached, running e2fsck is recommended
EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
init: cannot find '/system/bin/servicemanager', disabling 'servicemanager'
init: cannot find '/system/bin/vold', disabling 'vold'
init: cannot find '/system/bin/setup_fs', disabling 'setup_fs'
init: cannot find '/system/bin/netd', disabling 'netd'
init: cannot find '/system/bin/debuggerd', disabling 'debuggerd'
init: cannot find '/system/bin/rild', disabling 'ril-daemon'
init: cannot find '/system/bin/surfaceflinger', disabling 'surfaceflinger'
init: cannot find '/system/bin/app_process', disabling 'zygote'
init: cannot find '/system/bin/drmserver', disabling 'drm'
init: cannot find '/system/bin/mediaserver', disabling 'media'
init: cannot find '/system/bin/dbus-daemon', disabling 'dbus'
init: cannot find '/system/bin/installd', disabling 'installd'
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/keystore', disabling 'keystore'
init: cannot find '/system/bin/insmod', disabling 'mlan_insmod'
init: property (null) has no value for writing to /sys/class/android_usb/android0/iManufacturer
init: property (null) has no value for writing to /sys/class/android_usb/android0/iProduct
init: cannot find '/system/bin/sh', disabling 'console'
adb_bind_config
adb_open
android_work: sent uevent USB_STATE=CONNECTED
android_usb gadget: high speed config #1: android
android_work: sent uevent USB_STATE=CONFIGURED
IRQ112 -- no longer affine to CPU1
CPU1: shutdown