헥스파워시스텝의 유재규라고 합니다.

지난번에 알려주신 파일이 아니라.. 같은 폴더 있는.

ueventd.smdkv210.rc 요 파일에

/dev/ttyUSB0 0666 system system

을 추가해주면 권한이 바뀌네요..

지난번에 알려주신 방법으로 시도하여보았으나, 이루어지 지지 않아서 다시 문의드립니다.

현재 USB 디바이스를 연결해놓고 부팅하면 자동으로 감지하여

/dev/ttyUSB0라는 연결 다바이스가 생성이 됩니다.

물론 부팅이 완료된 상태에서 연결하여도 자동으로 인식되며 /dev/ttyUSB0 로 인식하고,

빼면 제거되고, 다시 연결하면 /dev/ttyUSB0로 연결됩니다.

제가 하고 싶은것은 부팅시에 권한을 주고자

device\samsung\smdkv210\init.smdkv210.rc 파일 부분에

on boot 또는 on fs 아래 부분에

지난번 답변으로 올려주신 내용을 추가하여

/dev/ttyUSB0 0666 system system

chmod 0666 /dev/ttyUSB0

같이 추가하여 컴파일을 진행하여 테스트 하여 보았으나,

이부분을 참조하는지 조차 의심스럽습니다.

컴파일 내역을 fastboot로 올리고 부팅한 결과 아래와 같이

아무일을 하지 않는것 같습니다.

확인하여 답변 주시면 감사하겠습니다.

즐거운 점심시간 되세요!!

V210 부팅과정 입니다.

OK

U-Boot 1.3.4 (Aug 16 2012 - 10:27:49) for MVV210

CPU:  S5PV210@1000MHz(OK)
        APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
        MPLL = 667MHz, EPLL = 80MHz
                       HclkDsys = 166MHz, PclkDsys = 83MHz
                       HclkPsys = 133MHz, PclkPsys = 66MHz
                       SCLKA2M  = 200MHz
Serial = CLKUART
Board:   MVV210-LCD-ICS
DRAM:    512 MB
Flash:   8 MB
SD/MMC:  7695MB
NAND:    256 MB
*** Warning - using default environment

In:      serial
Out:     serial
Err:     serial
checking mode for fastboot ...
Hit any key to stop autoboot:  0
reading kernel.. 1073, 8192
MMC read: dev # 0, block # 1073, count 8192 ...8192 blocks read: OK
completed
reading RFS.. 9265, 6144
MMC read: dev # 0, block # 9265, count 6144 ...6144 blocks read: OK
completed
Boot with zImage
get_format
-------- 1 --------
## Loading init Ramdisk from Legacy Image at 30a00000 ...
   Image Name:   ramdisk
   Created:      2013-03-27  10:15:50 UTC
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    163621 Bytes = 159.8 kB
   Load Address: 30a00000
   Entry Point:  30a00000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 3.0.8 (root@localhost.localdomain) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #1 PREEMPT Mon Mar 25 10:54:36 KST 2013
CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: SMDKV210
Ignoring unrecognised tag 0x41001099
Memory policy: ECC disabled, Data cache writeback
CPU S5PV210/S5PC110 (id 0x43110220)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000
S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
sclk_dmc: source is sclk_a2m (0), rate is 200000000
sclk_onenand: source is hclk_dsys (1), rate is 166750000
uclk1: source is mout_mpll (6), rate is 66700000
uclk1: source is mout_mpll (6), rate is 66700000
uclk1: source is mout_mpll (6), rate is 66700000
uclk1: source is mout_mpll (6), rate is 66700000
sclk_mixer: source is sclk_dac (0), rate is 54000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_cam0: source is ext_xtal (0), rate is 24000000
sclk_cam1: source is ext_xtal (0), rate is 24000000
sclk_fimd: source is mout_epll (7), rate is 80000000
sclk_mmc: source is mout_mpll (6), rate is 47642857
sclk_mmc: source is mout_epll (7), rate is 80000000
sclk_mmc: source is mout_mpll (6), rate is 47642857
sclk_mmc: source is mout_epll (7), rate is 80000000
sclk_mfc: source is sclk_a2m (0), rate is 200000000
sclk_g2d: source is sclk_a2m (0), rate is 200000000
sclk_g3d: source is sclk_a2m (0), rate is 200000000
sclk_csis: source is ext_xtal (0), rate is 24000000
sclk_spi: source is ext_xtal (0), rate is 24000000
sclk_spi: source is ext_xtal (0), rate is 24000000
sclk_pwi: source is ext_xtal (0), rate is 24000000
sclk_pwm: source is ext_xtal (0), rate is 24000000
s5p: 37748736 bytes system memory reserved for mfc at 0x3dc00000, 0-bank base(0x3dc00000)
s5p: 37748736 bytes system memory reserved for mfc at 0x4dbf5000, 1-bank base(0x4dbf5000)
s5p: 6291456 bytes system memory reserved for fimc0 at 0x4d5f5000, 1-bank base(0x4d5f5000)
s5p: 10137600 bytes system memory reserved for fimc1 at 0x4cc4a000, 1-bank base(0x4cc4a000)
s5p: 6291456 bytes system memory reserved for fimc2 at 0x4c64a000, 1-bank base(0x4c64a000)
s5p: 8388608 bytes system memory reserved for jpeg at 0x3d400000, 0-bank base(0x3d400000)
s5p: 7680000 bytes system memory reserved for fimd at 0x4bef7000, 1-bank base(0x4bef7000)
s5p: 8388608 bytes system memory reserved for pmem_gpu1 at 0x3cc00000, 0-bank base(0x3cc00000)
s5p: 3072000 bytes system memory reserved for g2d at 0x3c912000, 0-bank base(0x3c912000)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 99348
Kernel command line: console=ttySAC2,115200 init=/init
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 201MB 190MB 0MB = 392MB total
Memory: 389016k/511816k available, 12472k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xff000000 - 0xffe00000   (  14 MB)
    vmalloc : 0xe0800000 - 0xfd000000   ( 456 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0032000   ( 168 kB)
      .text : 0xc0032000 - 0xc0608c4c   (5980 kB)
      .data : 0xc060a000 - 0xc064dc80   ( 272 kB)
       .bss : 0xc064dca4 - 0xc078b868   (1271 kB)
SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:208
VIC @fd000000: id 0x00041192, vendor 0x41
VIC @fd010000: id 0x00041192, vendor 0x41
VIC @fd020000: id 0x00041192, vendor 0x41
VIC @fd030000: id 0x00041192, vendor 0x41
mult[140737]
max_delta_ns[2937815369]
min_delta_ns[30517]
rate[32768]
HZ[200]
Console: colour dummy device 80x30
Calibrating delay loop... 992.87 BogoMIPS (lpj=2482176)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys cpuacct
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
print_constraints: dummy:
NET: Registered protocol family 16
S3C Power Management, Copyright 2004 Simtec Electronics
---pmem_start is 0x4bef7000
smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
S5PV210: Initializing architecture
s3c-adc s5pv210-adc: attached adc driver
s3c24xx-pwm s3c24xx-pwm.3: tin at 4168750, tdiv at 4168750, tin=divclk, base 16
print_constraints: pd_tv_supply: 5000 mV normal
print_constraints: pd_lcd_supply: 5000 mV normal
print_constraints: pd_g3d_supply: 5000 mV normal
print_constraints: pd_mfc_supply: 5000 mV normal
print_constraints: pd_audio_supply: 5000 mV normal
print_constraints: pd_cam_supply: 5000 mV normal
bio: create slab <bio-0> at 0
print_constraints: B_PWR_5V: 5000 mV
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.3: using pins 110 (SDA) and 109 (SCL)
s3c-i2c s3c2440-i2c.0: slave address 0x10
s3c-i2c s3c2440-i2c.0: bus frequency set to 378 KHz
s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
s3c-i2c s3c2440-i2c.1: slave address 0x10
s3c-i2c s3c2440-i2c.1: bus frequency set to 65 KHz
s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
s3c-i2c s3c2440-i2c.2: slave address 0x10
s3c-i2c s3c2440-i2c.2: bus frequency set to 65 KHz
print_constraints: VALIVE_1.1V: 1100 mV
print_constraints: VUOTG_D+VUHOST_D_1.1V: 1100 mV
print_constraints: V_MIPI_1.8V: 1800 mV
print_constraints: VMMC+VEXT_2.8V: 2800 mV
print_constraints: VCC_2.6V: 2600 mV
print_constraints: VDAC_2.8V: 2800 mV
print_constraints: VUOTG_A+VUHOST_A_3.3V: 3300 mV
print_constraints: VADC+VSYS+VKEY_2.8V: 2800 mV
print_constraints: VCC_ARM: 750 <--> 1500 mV at 1250 mV
print_constraints: VCC_INTERNAL: 950 <--> 1200 mV at 1100 mV
print_constraints: VCC_MEM: 1800 mV
s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.24.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource clock_source_systimer
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 1, 12288 bytes)
UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 156K
PMU: registered new PMU device of type 0
Loaded driver for PL330 DMAC-0 s3c-pl330
        DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
Loaded driver for PL330 DMAC-1 s3c-pl330
        DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
Loaded driver for PL330 DMAC-2 s3c-pl330
        DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
ashmem: initialized
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 760
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
start plist test
end plist test
s3cfb s3cfb: xres: 800, yres: 480
s3cfb s3cfb: pixclock: 35247Khz
s3cfb s3cfb: xres: 800, yres: 480
s3cfb s3cfb: pixclock: 35247Khz
s3cfb s3cfb: xres: 800, yres: 480
s3cfb s3cfb: pixclock: 35247Khz
win->id=2, pmem_start=0x4c35c000
s3cfb s3cfb: [fb2] dma: 0x4c35c000, cpu: 0xe0c00000, size: 0x002ee000
s3cfb s3cfb: xres: 800, yres: 480
s3cfb s3cfb: pixclock: 35247Khz
s3cfb s3cfb: xres: 800, yres: 480
s3cfb s3cfb: pixclock: 35247Khz
FIMD src sclk = 166750000
s3cfb s3cfb: registered successfully
Start display and show logo
s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
console [ttySAC2] enabled
s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
PA FB = 0x4C35C000, bits per pixel = 32
screen width=800 height=480 va=0xdc35c000 pa=0x4c35c000
xres_virtual = 800, yres_virtual = 960, xoffset = 0, yoffset = 0
fb_size=3072000
Back frameBuffer[0].VAddr=dc4d3000 PAddr=4c4d3000 size=1536000
brd: module loaded
loop: module loaded
pmem_gpu1: 1 init
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
smsc911x: Driver version 2008-10-21
smsc911x-mdio: probed
smsc911x smsc911x: eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)
smsc911x smsc911x: eth0: MAC Address: 00:80:00:23:45:67
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
cdc_ncm: 04-Aug-2011
usbcore: registered new interface driver cdc_ncm
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
s5p-ehci s5p-ehci: S5P EHCI Host Controller
s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s5p-ohci s5p-ohci: EXYNOS OHCI Host Controller
s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
s5p-ohci s5p-ohci: irq 87, io mem 0xec300000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android_usb gadget: Mass Storage Function, version: 2009/09/11
android_usb gadget: Number of LUNs=1
 lun0: LUN: removable file: (no medium)
android_usb gadget: android_usb ready
Registered gadget driver 'android_usb'
mousedev: PS/2 mouse device common for all mice
input: s3c-keypad as /devices/platform/s3c-keypad/input/input0
samsung-ts s3c64xx-ts: driver attached, registering input device
input: s3c_ts as /devices/virtual/input/input1
        #SDKIM cma3000_driver_init
input: amosensor as /devices/virtual/input/input2
        #SDKIM cma3000_spi_probe
SPI setup failed
id:59 CMA3000_DEVICE_ID:37
SUCCESS: Sensor CMA3000(CHIP:59 REV:10)
CMA3000 regs: 59 10 10 08 00 00 00 00 00 08 33 08 1c 00 00
wake enabled for irq 175
GPIO Input Driver: Start gpio inputs for smdkv210-keypad in interrupt mode
input: smdkv210-keypad as /devices/virtual/input/input3
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
using rtc device, s3c, for alarms
s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
lirc_dev: IR Remote Control driver registered, major 251
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR LIRC bridge handler initialized
Linux video capture interface: v2.00
mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics

S3C JPEG Driver, (c) 2007 Samsung Electronics
JPEG driver for S5PV210
i2c i2c-1: attached s5p_ddc into i2c adapter successfully
S5PC11X HPD Driver, (c) 2010 Samsung Electronics
S5PC11X CEC Driver, (c) 2010 Samsung Electronics
samsung-fake-battery samsung-fake-battery: samsung_fake_bat_probe
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 3: sclk_mmc (47642857 Hz)
mmc0: no vmmc regulator found
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.3: clock source 3: sclk_mmc (47642857 Hz)
mmc1: no vmmc regulator found
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
logger: created 256K log 'log_main'
logger: created 256K log 'log_events'
logger: created 256K log 'log_radio'
logger: created 256K log 'log_system'
Error: Driver 'samsung-audio' is already registered, aborting...
mvv210_wm8580_gpio_irq request_irq OK gpio:133 irq:37
asoc: wm8580-hifi-playback <-> samsung-i2s.0 mapping ok
mvv210_wm8580_gpio_irq request_irq OK gpio:135 irq:39
asoc: wm8580-hifi-capture <-> samsung-i2s.0 mapping ok
ALSA device list:
  #0: SMDK-I2S
TCP cubic registered
NET: Registered protocol family 10
Mobile IPv6
IPv6 over IPv4 tunneling driver
mmc0: new high speed SDHC card at address b368
mmcblk0: mmc0:b368 SDC   7.51 GiB
NET: Registered protocol family 17
NET: Registered protocol family 15
 mmcblk0: p1 p2 p3 p4
NET: Registered protocol family 35
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
regulator_init_complete: VDAC_2.8V: incomplete constraints, leaving on
regulator_init_complete: pd_cam_supply: incomplete constraints, leaving on
regulator_init_complete: pd_mfc_supply: incomplete constraints, leaving on
regulator_init_complete: pd_tv_supply: incomplete constraints, leaving on
s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-04 02:57:40 UTC (946954660)
FIMC0 registered successfully
FIMC1 registered successfully
FIMC2 registered successfully
S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
usb 2-1: new full speed USB device number 2 using s5p-ohci
s5p-tvout s5p-tvout: hpd status is cable removed
Freeing init memory: 168K
init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
pl2303 2-1:1.0: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB0
init: cannot open '/initlogo.rle'
EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
EXT4-fs warning (device mmcblk0p3): ext4_clear_journal_err:4154: Filesystem error recorded from previous mount: IO failure
EXT4-fs warning (device mmcblk0p3): ext4_clear_journal_err:4155: Marking fs in need of filesystem check.
EXT4-fs (mmcblk0p3): warning: mounting fs with errors, running e2fsck is recommended
EXT4-fs (mmcblk0p3): recovery complete
EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p4): warning: checktime reached, running e2fsck is recommended
EXT4-fs (mmcblk0p4): recovery complete
EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
android_usb: already disabled
adb_bind_config
adb_open
android_work: did not send uevent (0 0   (null))
/system/bin/sh: No controlling tty (open /dev/tty: No such device or address)
/system/bin/sh: warning: won't have full job control
android_work: sent uevent USB_STATE=CONNECTED
PVR_K:(Warning): SysFinalise: Version string: SGX540 S5PC110 [543, drivers/gpu/pvr/s5pc110/sysconfig.c]
root@android:/ # android_usb gadget: high speed config #1: android
android_work: sent uevent USB_STATE=CONFIGURED
win->id=0, pmem_start=0x4bef7000
s3cfb s3cfb: [fb0] dma: 0x4bef7000, cpu: 0xe3800000, size: 0x00465000
s3cfb s3cfb: [fb1] dma: 0x49400000, cpu: 0xffa00000, size: 0x002ee000
pmem: request for physical address of pmem region from process 2080.
warning: `zygote' uses 32-bit capabilities (legacy support in use)
request_suspend_state: wakeup (3->0) at 18898397058 (2000-01-04 02:57:55.103050362 UTC)
init: no such service 'dhcpcd_ip6tnl0'
init: no such service 'dhcpcd_ip6tnl0:-h android-653f061fb72f5981 ip6tnl0'
init: no such service 'dhcpcd_ip6tnl0'
acc_open
acc_release
init: no such service 'dhcpcd_ip6tnl0:-h android-653f061fb72f5981 ip6tnl0'